Cyberpunk 2077 dr12 quasar pistol

Thank you! I was hopping this could bridge the gap between pistol and cqb. Comes pre-short stroken even. Has potential if extra mags are available.
Might be limited by spring size looking at that plastic retainer.

Honestly, it would be quicker to open the mag door and dump gels in with a speed loader than swap mags😅
Extra mags are available tho🤔

1 Like

Say no more, ordered one with a mag. Should get here in time for a few mods and springtime.
Blue for me!

1 Like

Swapped to a longer Ausgel 7.5 barrel and picked up some FPS with fresh booms👍


4 Likes

Liking this, something different :+1:

Hopefully when I do the seals, it should clear 200fps🤔
I did notice another 5fps increase just by putting on the nadda hop-up, so I’m going to have a close look at the volumes .
I only hot glued the last part of the barrel in so it’s easier to do more swaps😬

3 Likes

Hi, do you think it’s possible to add a tracer unit or picatinny rails?

1 Like

An adapter would have to be made for the tracer unit, would have to be push fit.
Someone may be able to 3d print a front plate with treaded barrel section :thinking:
Still looking at pic rail options myself :sweat_smile:

2 Likes

this will be my first blaster, i was honestly just thinking about printing a rail out and drilling a couple holes through that outer casing to attach it, do you think if i go a longer internal barrel i could attach one to it that way? i have a little experence 3d printing got any ideas on what a base model should look like?

keep us posted i just purchased two, one for myself and the other for my brother. it’s our intro to the hobby so we are watching for mods

1 Like

Was going to do the same with a rail, just gotta pull it down again to make sure the screws aren’t going to interfere with the gearbox first😬
Have other people’s stuff I have to finish first😅
The nadda hop-ups should push straight in on the original barrel

1 Like

do you think super glue would be the better option then?

Probably not🤔
Being a split body blaster, gluing it would mean you won’t be able to get the body to open for repairs/mods.
Top pic rail anyway

1 Like

Got my clue blaster in today. Dont have time to play with yet, but let loose a few hundred rounds.
On stock 2s lipo, did 10 rps, hanging around 150 fps. VERY old milkies used.
Mag is smaller then Id like, didnt get a count but probably 75 with another 15 in the feeder tube.
Ergonomics not the best for me, pushed hard on the base of my thumb but did like being able to hold it like a mini m4.
Single shot will feed double, blank, double, blank ect so has something funky going on inside.
Battery comartment is tiny, the stock lipo barely fits.
Overall, its a decent little package. Its for my 5 yo and I think it will fit him well. Its small, light and after some mods, should do what I want it to do.

4 Likes

Noiiiiiice :sunglasses:
I took mine out for one end of a game on the weekend as I was testing the mosfet in the baby Barrett.
Actually got 4 kills with it🤣

3 Likes

yeah got mine yesterday, was playing with it and noticed the double feeds thinking it was the gellets that came with the blaster but if you figure out any mods for it please let us know

Did a tear down. Wanted to add longer barrel, or at least match ve ratio. A stronger spring, lube and tighten up seals. Theres tooany screws to take apart, and a hidden screw or 2.
The gearbox is the same, or at least very similar to the bf mac 10. Thoes can be gotten in metal but i image would need a bit of custom work to fit. As soon as I lwt loose the last screw, it sproinged l apart. Yay.

Some poor craftmanship went into the soldering. Id expect this to be neg, but not positive. Both leads were red, so not positive.

Barrel is a thin walled alum. Mine was glued in with super glue, or similar. Was a bitch to get out. Esp since the t piece is either not nylon or a good nylon. Its a 7.8mm id, and im hoping that explains my double feed issue. Replaced with a 130mm 7.5 barrel to closer match ve.


3 Likes

Some random measurments





5 Likes

Assembled gearbox gears, hopfully correct as its a bitch to keep all the springs from popping out.

No way in hell Id beable to get a pic with cylinder, tappet and main spring. Already needed an extra hand to put it together. Stock did come with 1 shim, so thats encouraging. I couldnt test shimming because there isnt access to the gears once closed.

The cylinder seal wasnt the best. I cut a standard green ring up to be a bit smaller, glued it amd stuffed it in. Its better but not great. The nozzle leakes pretty good. Some thick grease helped.

Now iv too many drinks to continue the rest. Will wrap it up tomorrow for testing.

5 Likes

I was looking at one of these gearboxes as they seem identical

2 Likes