Ohh hell yea… movie night
WAIT your telling me there is a YouTube channel for people wearing gas masks.
And it’s not connected to porn in anyway.
2 Likes
You sit side saddle? 
i mean I turned it sideways for picture, its a kneelin chair
As promised the video is up hope you guys enjoy and feedback is highly appreciated.
5 Likes
Got one of these for $269
2 Likes
Nice gat, nice price! 
Good video, might end up binging these, asmr and learning, also is the nose springloaded to block the hole when you take out the canister?
sidenote I know gas masks are more your fixation, but check out the ww1 splatter mask, it was issued to tankers to help deal with the armour spauling when it got hit, so it looks cool and weird
I am kinda upset thats your only video, its so good I was gonna watch morrreee, makin me wait ya muthafucka
I’m subbed, but yknow… youtube, so lemme know when you make another, I’d like to watch it ^^
Cool vid, very informative.
Squids youtube career begins…
2 Likes
The inhale valve where the filter is screwed into isn’t spring loaded the little rubber pad you see is to stop you from exhaling air through the filter which would expire the filters quicker. Glad you enjoyed the video there is more to come eventually
2 Likes
Got another ww2 mask on the way so expect a video about a week or so after it arrives
3 Likes
I don’t usually watch these types of videos, but I thought I’d make an exception. I really did enjoy the video, very interesting. Looking forward to seeing some more.
1 Like
Cheers appreciate the support
Flashlight seems legit, though two buttons makes for confusinf controls.
I am kinda unsure how to get the loop on but it was off ali not ebay so scared it wont fit dont wanna break my torch or anything yknow
Mine should be here tomorrow, I’ll film myself putting it on.
1 Like
Sorry, I was expecting to have a phone to film it for you, but my new one that showed up today. Well…
So it was back in the box when I put my Switchback on. Either way…
- Remove the pocket clip
- Unscrew the tailcap and remove the battery
- Place the Switchback on the tail end of the light, with the pocket clip facing towards the head.
- Place the rear (diagram red) edge of the switchback against a doorway, and push HARD on the bezel until half of the switchback slips over the threads. It’ll be kind of half-on, half-off.
- Put your hand on the rear of the Switchback and start pushing the two halves together while twisting.
- Eventually the Switchback will pop over the rest of the way, and come to rest in the pocket clip groove with about 5mm of play forward/backwards. It will be slack and terrible, this is normal.
- Put your battery back in, and add your tail cap, if you haven’t already. Lock the light out.
- With the front of the Switchback (thick green line of the diagram) slid as far back as you can freely can (thin green line), roll your first O-ring down the front of the torch so that it falls into the pocket-clip groove.
- The front edge of the Switchback has a lip on it so that it doesn’t slide all the way back off again. That lip has a gap in it, about 1cm wide. Locate this now.
- Take a plastic tool like a spatula or a butter knife, and shove the O-ring into that gap in the lip.
- While continuing to apply pressure on your plastic tool, twist the Switchback around 360 degrees. This should schlorp the O-ring under the Switchback.
- Add 2 more O-rings, and tension as desired.
1 Like
WTAF! Sounds like the instructions for building a bloody Space Shuttle! 
1 Like
Lmao. Honestly for someone better versed in metal strengths and stuff like you, I’d just say
“Take the tail cap off, jam the switchback on (don’t be gentle), and put some O-Rings under it”, but Puppy seemed to be struggling, so he gets the NASA manual 